FORTRESS OF INDUSTRIAL FASTENERS

Corporate

Used in automotive applications, plumbing, and more, flange bolts feature a washer like flange beneath the bolt head that speeds production time and distributes the clamping load, offering protection to the mating surface.

Stud Bolts are externally threaded fasteners without a head, used with 2 nuts on either side, substituting a usual "bolt & nut" assembly. Stud bolts are prominently used in flange connections. Depending upon their design and threading patterns, We have all types of stud bolts as below.

Wing nuts are used when a part is often assembled and disassembled by hand, where no more than finger pressure is needed. They may be used with or without a washer. The ease of use also make wing nuts popular for applications in which convenience is vital, such as on boats and bicycles.

Hex Nuts. Hex nuts are a six‑sided nut and are the most commonly shaped nut today. They are used with anchor shackles, bolts, screws, and other externally threaded components. Hex nuts, in conjunction with these other fasteners, are used to connect both metal and wood components to prevent tension and movement.

The Nylock nut is an economic locking nut and ideal in applications where vibration or motion could loosen or undo the nut. The nut can also be used to assist sealing the bolt thread against seepage of oil, water, petrol, paraffin and other liquids.

Hex dome nuts or acorn nuts got their names due to the dome-shaped projection on one side of the nut. This is mostly used to protect objects close to the ends of screws from scratches and structural injuries. It also reduces the effects of physical mishaps on human skin if it somehow forcefully hits the fasteners.

To distribute the fastener's load while reducing heat and friction during the tightening process. They can also be used as spacers, as is common in industrial and domestic applications. Flat washers are also called on to provide electrical insulation.

Self tapping screws are mostly used when the medium into which it will be screws is something like metal. Although, self tapping screws are also used to drill wooden and plastic materials. They tend to have a sharp point, and the threads are also sharp to act like knives cutting into any kind of medium.

Grub screws, also known as set screws, are a type of fixing screw that's most often used to join one component or part securely to another.

U-bolts have primarily been used to support pipework, pipes through which fluids and gasses pass. As such, U-bolts were measured using pipe-work engineering speak. A U-bolt would be described by the size of pipe it was supporting. U-bolts are also used to hold ropes together.

Strut channel is used to mount, brace, support, and connect lightweight structural loads in building construction. These include pipes, electrical and data wire, mechanical systems such as ventilation, air conditioning, and other mechanical systems.

Concrete Wedge Anchors are used to anchor and secure materials and equipment to solid concrete masonry surfaces.

Pin type anchor bolts find their use in soft masonry to reduce the effect of vibration and pressure. The most significant advantage of using these bolts is that it can be replaced without affecting the holding strength of the anchor system.

This Bullet Type Anchor Fastener is used for fixing lightweight equipment to ceiling and wall by using threaded rods, attaching pipe work to concrete ceiling and wall and ideal for fixing stair case

Rawl anchor bolts are used primarily to install structures to concrete, brick, block, and stone. Rawl Anchor Bolts are quick and simple to use through bolts, drop-in anchors with internal thread, Safety Plus anchors for highest loads, and cutting-edge concrete screw bolts

High Tensile Hex Bolt is used in applications which have high stress on the fasteners. When connecting two parts together, the tensile stress forced on the fastener can break it.

High Tensile Nuts are ideal for fastening metal to metal and metal to timber. They are commonly used for securing the two objects where there is access to the backside to install a nut onto a bolt.

High Tensile engineer Washers are flat washers that have been machined to comply with specific standards and tolerances, suitable for high tensile applications. Washers are used to distribute the load under the bolt/screw or under a nut when fastening.

Commonly used in machine parts, die fixture, and clamping, Allen head screws enable you to drive in and secure this type of fastener where there is not sufficient space to use a traditional socket or wrench.

The allen cap can be tightened and loosened with allen keys. These are useful to install the screws into limited and narrow space. The CSK Allen Head Screw is used in wooden, metallic, marine, general corrosive and many other domestic application types.

Threaded rods have many applications, effectively working as a pin to fasten or connect two materials together. Also used to stabilise structures, they can be inserted into various materials like concrete, wood or metal to either temporarily create a steady base during construction or they can be installed permanently.

Spring washers are normally made out of spring steel and are hardened to HV 430 to 530 and are used along with almost every externally threaded fastener. Due to their Spring action, they give a locking effect to the tightened fastener, when fastened with Spring washer.

The allen cap can be tightened and loosened with allen keys. These are useful to install the screws into limited and narrow space. The CSK Allen Head Screw is used in wooden, metallic, marine, general corrosive and many other domestic application types.